Influence of yttrium concentration and deposition method on the crystal lattice parameters of KNA-82 sealing coatings

dc.contributor.authorFasol, Yelyzaveta
dc.contributor.authorKubich, Vadim
dc.contributor.authorRyabenko, Anton
dc.contributor.authorФасоль, Єлизавета Олександрівна
dc.contributor.authorКубіч, Вадим Іванович
dc.contributor.authorРябенко, Антон Євгенович
dc.date.accessioned2026-11-17T08:47:42Z
dc.date.available2026-11-17T08:47:42Z
dc.date.issued2026
dc.descriptionFasol Yelyzaveta, Kubich Vadim, Ryabenko Anton. Influence of yttrium concentration and deposition method on the crystal lattice parameters of KNA-82 sealing coatings. Нові матеріали і технології в металургії та машинобудуванні. 2026. № 3. С. 23-28.
dc.description.abstractEN: Purpose. To establish the patterns of changes in the crystal lattice parameters of the KNA-82 sealing coating depending on the yttrium concentration within the range of 0.1–0.5 wt.% and the deposition method -flame spraying and ion-plasma deposition and to determine the alloying range in which structural changes are most controllable. Research methods. The lattice parameters were determined by X-ray diffraction analysis using CuKα radiation (λ = 1.5418 Å). Interplanar spacings were calculated according to the Wulff-Bragg law, while the cubic lattice parameters were determined using the Miller indices of the diffraction peaks. The initial diffraction angles and calculated values were obtained from the experimental data table. Results. For ion-plasma coatings, increasing the Y content from 0.1 to 0.5 wt.% resulted in an increase in both analyzed lattice parameters: from 4.0525 to 4.0543 Å and from 4.2297 to 4.2332 Å. For flame-sprayed coatings, the dependence was non-monotonic: at 0.3 wt.% Y, a local decrease to 4.0519 and 4.2322 Å was observed, followed by an increase to 4.0567 and 4.2356 Å at 0.5 wt.% Y. The most pronounced difference between the deposition methods was observed at 0.3 wt.% Y. Scientific novelty. The regularities of the effect of yttrium concentration within the range of 0.1–0.5 wt.% on the crystal lattice parameters of KNA-82 coatings were established. It was shown that the nature of structural changes depends significantly on the coating deposition method. The obtained results make it possible to substantiate a rational yttrium content with consideration of the deposition technology. Practical value. The obtained results can be used to select a rational yttrium content in KNA-82 coatings depending on the deposition method and the required structural characteristics. UK: Мета роботи. Встановити закономірності зміни параметрів кристалічної ґратки ущільнювального покриття КНА-82 залежно від концентрації ітрію 0,1–0,5 мас. % та способу нанесення – газополуменевого й іоноплазмового – і визначити діапазон легування, за якого структурні зміни є найбільш керованими. Методи дослідження. Параметри ґратки визначали за результатами рентгенівської дифрактоскопії з використанням CuKα-випромінювання (λ = 1,5418 Å). Міжплощинні відстані розраховували за законом Вульфа-Брегга, а параметри кубічної ґратки - за індексами Міллера дифракційних максимумів. Вихідні дифракційні кути та розрахункові значення взято з експериментальної таблиці. Отримані результати. Для іоноплазмових покриттів зі збільшенням Y від 0,1 до 0,5 мас. % обидва аналізовані параметри зростають: 4,0525→4,0543 Å та 4,2297→4,2332 Å. Для газополуменевих покриттів залежність немонотонна: при 0,3 мас. % Y спостерігається локальне зменшення до 4,0519 та 4,2322 Å, після чого при 0,5 мас. % значення зростають до 4,0567 та 4,2356 Å. Найбільша відмінність між способами нанесення зафіксована для 0,3 мас. % Y. Наукова новизна. Встановлено закономірності впливу концентрації ітрію 0,1–0,5 мас. % на параметри кристалічної ґратки покриття КНА-82. Показано, що характер структурних змін суттєво залежить від способу нанесення покриття. Отримані результати дозволяють обґрунтувати раціональний вміст ітрію з урахуванням технології напилення. Практична цінність. Отримані результати можуть бути використані для вибору раціонального вмісту ітрію в покритті КНА-82 залежно від способу його нанесення та необхідних структурних характеристик.
dc.identifier.urihttps://eir.zp.edu.ua/handle/123456789/33056
dc.language.isoen
dc.publisherНаціональний університет "Запорізька політехніка"
dc.subjectKNA-82
dc.subjectyttrium
dc.subjectcrystal lattice parameter
dc.subjectX-ray diffraction analysis
dc.subjectflame spraying
dc.subjection-plasma deposition
dc.subjectgas turbine engine
dc.subjectущільнювальне покриття
dc.subjectітрій
dc.subjectпараметр кристалічної ґратки
dc.subjectрентгенівська дифрактоскопія
dc.subjectгазополуменеве напилення
dc.subjectіоноплазмове напилення
dc.subjectгазотурбінний двигун
dc.subjectsealing coating
dc.titleInfluence of yttrium concentration and deposition method on the crystal lattice parameters of KNA-82 sealing coatings
dc.title.alternativeВплив концентрації ітрію та способу нанесення на паметри кристалічної ґратки ущільнювальних покриттів КНА-82
dc.typeArticle

Files

Original bundle

Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
S_23 Fasol.pdf
Size:
894.69 KB
Format:
Adobe Portable Document Format

License bundle

Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
license.txt
Size:
1.71 KB
Format:
Item-specific license agreed upon to submission
Description: