Електротехніка та електроенергетика - 2014, №1
Permanent URI for this collectionhttps://eir.zp.edu.ua/handle/123456789/27625
Browse
Recent Submissions
Item Повышение эффективности преобразования энергии в ветроэлектрических установках с аэродинамической мультипликацией(Національний університет "Запорізька політехніка", 2014) Немудрый, Игорь Юрьевич; Немудрий, Ігор Юрійович; Nemudry, I. Y.RU: В статье рассмотрены направления повышения эффективности принципиально новой схемы ветроэлектрических установок (ВЭУ) с аэродинамической мультипликацией (АМ), обеспечивающих работу с сетью без преобразователей частоты при переменных оборотах ветроколеса. Показана возможность использовать высокочастотные генераторы с совмещенными обмотками для повышения единичной мощности ВЭУ АМ свыше 1000 кВт. Рассмотрены возможности использования в преобразователях частоты ведомых сетью инверторов (ВСИ) с преобразователями повышающего напряжения и автономных инверторов напряжения (АИН). Для обеспечения электромагнитной совместимости с сетью приведены рекомендации по выбору схем преобразователей частоты. UK: В статті розглянуті напрями підвищення ефективності принципово нової схеми вітроелектричних установок (ВЕУ) з аеродинамічною мультиплікацією (АМ), що забезпечують роботу з мережею без перетворювачів частоти при змінних обертах вітроколеса. Для підвищення одиничної потужності ВЕУ АМ більш ніж 1000 кВт можливе використання високочастотних генераторів з суміщеними обмотками. Розглянуті можливості використання в перетворювачах частоти інверторів керованих мережею (КМІ) з перетворювачами підвищення напруги ф автономних інверторів. Для забезпечення електромагнітної сумісності з мережею наведені рекомендації по вибору схем перетворювачів частоти. EN: In the article the directions of the efficiency increase of the fundamentally new scheme of wind power equipment with an aerodynamic animation (WPE AAS) are reviewed, this scheme provides operation with network without frequency converters at variable speed wind turbine. On simulation models, the dependences of the energy produced at different speeds of wind turbines depending on the speed of the wind flow are given. It is shown that the use of auxiliary frequency converters with power up to 20 % of nominal allows to increase electricity production by 3 % to 10 % at the speed of the wind flow ≤5 m/S and by reducing the speed of the wind turbine in 2 times. High efficiency is provided by series connection of the rectifier and the adjustment of excitation current of the generator. For increasing the unit capacity of wind turbines WPE Aa to more than 1000 kW it is possible to use high-frequency inductor generators with a combined windings. It is shown that the frequency of the generator 125 Hz approximately twice reduced the weight of the generator when saving power. The complex generator – FC provides increased efficiency by 1,6 % and 2,7 %. The possibilities of inverters slave network (ISN) use in frequency converter with boost converters of voltage and standalone inverters are presented. The developed recommendations on determination of the Converter parameters increase tension and requirements for internal resistance of the generator and power cables. It is established that the use of multiphase ISN can significantly reduce the cost of powerful wind farms connected to the transmission line high voltage over 100 kV by reducing the installed power of shunt reactors. To ensure electromagnetic compatibility with the network the guidance on the choice of schemes of multiphase frequency converters with ISN is given.Item Особенности идентификации интенсивности солнечной радиации при проектировании солнечных электростанций(Національний університет "Запорізька політехніка", 2014) Ярымбаш, Дмитрий Сергеевич; Даус, Юлия В.; Яримбаш, Дмитро Сергійович; Даус, Юлія В.; Yarymbash, D. S.; Daus, Y. V.RU: Для оценки энергетического потенциала солнечной энергии района установки солнечной электростанции предложена методика определения энергетического потока солнечной радиации, основанная на комбинации метода применения дневного профиля поступления солнечной радиации при абсолютно чистом небе и актинометрических данных электронной базы NASA, с последующей идентификацией характеристик энергетического потока методами разделения переменных и аппроксимации. Методика учитывает географические координаты, реальные атмосферные условия, обладает высокой точностью и вычислительной эффективностью. UK: Для оцінки енергетичного потенціалу сонячної енергії району установки сонячної електростанції запропонована методика визначення енергетичного потоку сонячної радіації, заснована на комбінації методу застосування денного профілю надходження сонячної радіації при абсолютно чистому небі і актинометричних даних електронної бази NASA, з подальшою ідентифікацією характеристик енергетичного потоку методами розділення змінних та апроксимації. Методика враховує географічні координати, реальні атмосферні умови, володіє високою точністю і обчислювальної ефективністю. EN: For solar power stations designing it is proposed method of any point solar radiation energy flux calculation knowing only its geographical coordinates based on a combination of the perfectly clear sky solar radiation daily profile application model and NASA solar radiation data base with the subsequent energy flow characteristics identification by the method of variables separation and approximation, that takes into account the region real atmospheric conditions providing high calculation accuracy of the all solar radiation components and the numerical implementation efficiency. The identification of the real atmospheric conditions adaption factor dependence on the solar power plants installation geographical coordinates is determined on the basis of cubic spline interpolation. Therefore, it can be used to determine the total solar radiation intensity at the designing solar installations initial stage.Item Энергосистема будущего. Концепция Smart Grid. Специфика реализации на Украине(Національний університет "Запорізька політехніка", 2014) Ткаченко, С. Н.; Ткаченко, С. М.; Tkachenko, S. N.RU: Работа посвящена проблематике построения электроэнергетических систем будущего. Детально рассмотрены все современные стратегические направления развития источников генерации электроэнергии и энергосистем в целом. Отдельным пунктом выделены энергосистемы концепции Smart Grid с большой долей возобновляемых источников энергии, а также специфика реализации на Украине. Рассмотрен проект сооружаемого в ДонНТУ учебно-научного центра «Smart Grid – ДонНТУ», в котором реализована физическая модель «интеллектуальной» энергетической системы. UK: Робота присвячена проблематиці побудови електроенергетичних систем майбутнього. Детально розглянуто всі сучасні стратегічні напрямки розвитку джерел генерації електроенергії та енергосистем у цілому. Окремим пунктом виділено енергосистеми концепції Smart Grid з великою часткою поновлюваних джерел енергії, а також специфіка реалізації на Україні. Розглянуто проект навчально-наукового центру «Smart Grid – ДонНТУ», що споруджується у ДонНТУ, в якому реалізована фізична модель «інтелектуальної» енергетичної системи. EN: Work is dedicated to a perspective of electrical power systems creation of the future. All modern strategic directions of generation sources development of the electrical power and power supply systems as a whole are in details considered. Special item in work is allocated to power supply systems of the Smart Grid conception with a big share of renewable energy sources, and also specificity of their realization in Ukraine. The project of educational scientific center «Smart Grid – DonNTU» constructed in Donetsk National Technical University in which the physical model of an «intellectual» power system is realized is considered. The power part of «Smart Grid – DonNTU» laboratory represents block structure in which in the blocks form such models are realized: physical model of a thermal power plant, a real solar power plant, wind turbines models, energy stores, reactive power compensators. The special bench for detailed studying of modern digital relay protection of the SiprotecTM series of Siemens® production is also realized. The physical model of the condensation turbine of a thermal power plant, and also models of wind-generating installations are executed by means of induction electrical motors with the short-circuited rotor, established on one shaft with generators of AC current. The solar power plant realized in laboratory, represents fifty five modern solar panels of the Ukrainian production with a total power of 10 kW. As model of hydrogen installation with hydrogen fuel cells in the project was accepted the educational station «Nexa® Lernsystem» with a rated power of 1,2 kW was created. This installation is equipped with necessary monitoring and optimization systems, and also built-in system of power management. At creation of laboratory installation the principle of maintenance in node constant value of reactive power due to use of dynamical reactive power compensators that will allow providing the maximum speed of the compensator is assumed as a basis and to increase its efficiency. By means of the PROFIBUS data bus all elements of physical model is integrated into the general control system of laboratory. In total this laboratory allows to model physically different normal, abnormal and emergency conditions of power supply systems of the Smart Grid conception work.Item Совершенствование пусковых органов БАВР в системах электроснабжения с двигательной нагрузкой(Національний університет "Запорізька політехніка", 2014) Сивокобыленко, В. Ф.; Деркачев, С. В.; Сивокобиленко, В. Ф.; Деркачов, С. В.; Sivokobilenko, V. F.; Derkachov, S. V.RU: Рассмотрен способ повышения надeжности систем электроснабжения с двигательной нагрузкой при кратковременных нарушениях электроснабжения за счeт совершенствования пусковых органов быстродействующего автоматического включения резерва (БАВР) на основе предложенного метода ускоренного определения комплексных мгновенных значений токов и напряжений прямой и обратной последовательностей. Приведен пример успешного действия устройства БАВР с использованием предложенного подхода. UK: Розглянуто спосіб підвищення надійності систем електропостачання з двигуновим навантаженням при короткочасних порушеннях електроживлення за рахунок вдосконалення пускових органів швидкодіючого АВР на основі запропонованого методу прискореного визначення комплексних миттєвих значень струмів та напруг прямої та зворотної послідовності. Наведено приклад успішної дії пристрою швидкодіючого АВР з використанням запропонованого підходу. EN: Method for increasing of fast-acting automatic transfer switch The method for reliability of increasing of electrical power supply system with motor load at short-time power failure by improvement of fast-acting automatic transfer switch starting element is considered. Starting element of fast-acting automatic transfer switch on proposed method is based on definition of the angles between direct sequence voltages on main and reserve power sources and between direct sequence currents on main and reserve power sources. Definition of direct and inverse sequences currents and voltages values on introduced method is based on measuring and processing of current and voltage momentary values. The example of the fast-acting automatic transfer switch successful operation with using of the offered approach is given.Item Визначення динамічних індуктивностей асинхронного двигуна з урахуванням процесів насичення(Національний університет "Запорізька політехніка", 2014) Кулагін, Дмитро Олександрович; Kulagin, D. O.UK: Встановлена математична залежність між динамічними індуктивностями асинхронної машини та параметрами насичення, що є необхідним при оптимізації енергетичних характеристик в залежності від навантаження на електропривод при роботі зі зниженим значенням модуля вектора потокозчеплення ротора. Проведене дослідження виконано в загальному вигляді, що дозволяє використовувати його результати для асинхронних двигунів різних серій. EN: Definition of dynamic inductances of the asynchronous engine with regard to processes of saturation Development of mathematical model of asynchronous machines in (d, q) coordinate system with taking into account the saturation of magnetic circuits is performed. In the paper, we used the method of dynamic inductances, which is connected with the use of a systematic study of motor properties. An analytical model of asynchronous motor magnetic circuit, which is taken into account action of the tangential and radial dynamic inductances is created. On the basis of this the sensor dynamic inductances of rich machine, which was recorded in (d, q) coordinate system of equations of rotor and stator circles of asynchronous motor with the saturation were built. The author suggests to use the method of dynamic inductances at construction of asynchronous engine mathematical model, that allows to take into account the saturation of the main magnetic path for the modes with a wide range of changes in the flow of mutual induction between the stator and the rotor, saturation flow path, the scattering modes that are characterized by large current circuits of the machine, induction, due to processes of saturation, between mutually perpendicular to the contours of the machine, as well as the joint saturation worker thread and threads scattering modes that are characterized by the significant size of the workflow and large values of currents contours of the machine. The mathematical model allows to take into account the change of the magnetic state of asynchronous motor as necessity to build adequate systems of control drives and driving.Item Модернізація лабораторного стенда дослідження асинхронного електропривода(Національний університет "Запорізька політехніка", 2014) Крисан, Юрій Олексійович; Krysan, Yu.UK: Модернізовано лабораторний стенд для дослідження режимів роботи асинхронного електропривода з використанням сучасного мікропроцесорного реле фірми Moeller. EN: The worked out stand is based on the basis of existed laboratory equipment for research of the different modes of asynchronous electric drive. For a management the modes of starting and braking with the Moeller microprocessor relay is used. The offered solution of modernization allows simultaneously to investigate work of electromechanical control system, realized on classic to the relay – contact base of management, and system, realized on a modern microprocessor equipment, and also to conduct the necessary tuning of stand constituents and investigate the transient of current slip-ring induction motoring. An equipment allows to put right and test the next modes: rheostat starting slip-ring induction motoring in the functions of time, reverses, dynamic braking. The worked out course of laboratory works allows to conduct timing of switching of degrees of resistances and construction of electromechanical descriptions slip-ring induction motoring and also to design his work using the SimPowerSystems libraries of МATLAB Simulink package. Creation of program algorithm and its realization as a EASYSOFT program environment are performed. Verification of rightness of the program writing and tuning of all program elements parameters are done. It is shown that the removal of the real current is in the phase of rotor (by means of digital oscillograph) and it is don’t the design comparison of its results.Item Особенности мониторинга технического состояния основной изоляции высоковольтных вводов и трансформаторов тока(Національний університет "Запорізька політехніка", 2014) Андриенко, Петр Дмитриевич; Сахно, Александр Анатольевич; Конограй, С. П.; Спица, А. Г.; Скрупская, Людмила Степановна; Андрієнко, Петро Дмитрович; Сахно, Олександр Анатолійович; Конограй, С. П.; Спица, А. Г.; Скрупська, Людмила Степанівна; Andrienko, P. D.; Sakhno, A. A.; Konogray, S. P.; Spitsa, A. G.; Skrupskaya, L. S.RU: В статье представлен анализ особенностей мониторинга технического состояния основной изоляции трансформаторов тока и вводов с точки зрения выбора диагностических параметров, описаны результаты измерения характеристик частичных разрядов в изоляции трансформаторов тока и вводов различными приборами и сделаны выводы по целесообразности контроля этих параметров, а также предложен подход к измерению характеристик частичных разрядов в изоляции при эксплуатации вводов и трансформаторов тока, предложен подход к использованию полученных значений диагностических параметров для оценки остаточного ресурса высоковольтных трансформатора тока и вводов. UK: У статті представлено аналіз особливостей моніторингу технічного стану головної ізоляції трансформаторів струму та уводів з точки зору вибору діагностичних параметрів, описано результати вимірювання характеристик часткових розрядів в ізоляції трансформаторів струму та уводів різними приладами та зроблено висновки по доцільності контролю цих параметрів, а також запропоновано підхід до виміру характеристик часткових розрядів в ізоляції під час експлуатації уводів та трансформаторів струму, запропоновано підхід до використання отриманих значень діагностичних параметрів для оцінки залишкового ресурсу високовольтних трансформаторів струму та уводів. EN: The article devoted to an analysis of monitoring features of basic insulation condition, in terms of diagnostic parameters choice, it describes the measuring results of the partial discharges characteristics in bushings and current transformers by various devices. The usage of tan-delta for online monitoring of bushings and current transformers was justified. The usage of term «discharge activity» instead on «partial discharge» for online monitoring was justified, the examples of discharge activity measurement by various devices is represented. Approach to measuring partial discharge in the insulation during equipment operation was proposed. It lies in simplified spectral analysis of the high-frequency signal from the bushing test-tap and grounding of equipment. The approach to the using of the obtained values of diagnostic parameters, including partial discharges or so called «discharge activity», for assessing the remaining life of the current transformer and high voltage bushings based on Cox model and «fuzzy» logic algorithms was proposed.Item Конвективный и лучистый теплообмен при плавлении проволоки в струе дуговой плазмы(Національний університет "Запорізька політехніка", 2014) Ершов, Анатолий Васильевич; Зеленина, Елена Анатольевна; Єршов, Анатолій Васильович; Зеленіна, Олена Анатоліївна; Yershov, A.; Zelenina, E.RU: Рассмотрены особенности конвективного и лучистого теплообмена поперечного потока аргоновой плазмы с поверхностью оплавленного торца стальной проволоки. Показано, что конвективный тепловой поток сосредоточен на лобовой расплавленной поверхности металла, а не на всей поверхности проволоки. Выполнен расчет плотности теплового потока объемного излучения плазмы. Показано, что сферический слой плазмы аргона радиусом 2 мм является оптически прозрачным в интервале температур (8–20) 103 К, поскольку степень черноты этого слоя существенно меньше единицы. Определено, что плотность теплового потока излучения поверхности стального электрода пренебрежимо мала по сравнению с излучением плазмы с температурой столба 12 103 К. UK: Розглянуто особливості конвективного і променистого теплообміну поперечного потоку аргонової плазми з поверхнею оплавленого торця сталевого дроту. Показано, що конвективний тепловий потік зосереджено на лобовий розплавленої поверхні металу , а не на всій поверхні дроту. Виконано розрахунок щільності теплового потоку об’ємного випромінювання плазми. Показано, що сферичний шар плазми аргону радіусом 2 мм є оптично прозорим в інтервалі температур (8–20) 103 К, оскільки ступінь чорноти цього шару істотно менше одиниці. Визначено, що щільність теплового потоку випромінювання поверхні сталевого електрода мала в порівнянні з випромінюванням плазми з температурою стовпа 12·103 К. EN: The features of convection and radiant heat exchange of argon plasma cross flow from the surface of the melted butt of steel wire with plasma coating on metal surface are considered. We investigated the uneven distribution of convective heat flow around the perimeter of the heating wire The main part of convective heat flux of plasma centered on its wire is shown,. The density of convective heat flow in the neighborhood of its critical point during the heating of the plasma flow in a wire coating is defined. Calculation of the heat flux density is a 3-d plasma radiation. It is shown that the spherical layer of 2 mm radius of argon plasma is optically transparent in the temperature range (8–20) 103 k, since the degree of this layer blackness is considerably less than one. It is determined that the density of heat flow radiation of steel electrode surface is negligible compared with the radiation from the plasma column with the temperature 12·103 К.Item Особенности ударного теплового воздействия на асинхронный двигатель с модифицированной системой импульсного регулирования в условиях частых пусков(Національний університет "Запорізька політехніка", 2014) Коцур, Михаил Игоревич; Коцур, Михайло Ігорович; Kotsur, M.RU: Проведена сравнительная оценка скорости нарастания температуры не управляемого асинхронного двигателя с фазным ротором и с модифицированной системой импульсного регулирования в цепи ротора в условиях частых пусков, в зависимости от интенсивности его разгона. Разработаны рекомендации по оптимальному управлению асинхронным двигателем с модифицированной системой импульсного регулирования, обеспечивающие наилучший тепловой режим при его пуске. UK: Проведена порівняльна оцінка швидкості наростання температури некерованого асинхронного двигуна з фазним ротором, а також з модифікованою системою імпульсного регулювання в колі ротора в умовах частих пусків, в залежності від інтенсивності його розгону. Розроблені рекомендації щодо оптимального керування асинхронним двигуном з модифікованою системою імпульсного регулювання, які забезпечують найкращій тепловий режим при його пуску. EN: Currently there is no information about the optimal value of the rate of change pulse duty factor coefficient in speedingup modes of asynchronous motor (AM) with the modified pulse control system, where the impact components of the thermal effect intensity is the lowest one. The aim is to estimate the derivation of the stator temperature, the temperature of AM with the modified system in conditions of frequent starts, depending on the intensity of its speed up. To estimate the derivation of the stator temperature, the temperature of AM with the modified system, depending intensity of its speed up the complex simulation model of electromagnetic and thermal process are designed. This model describes the thermal transient process in structural elements of AM and allows considering peculiarities of electromagnetic energy transformation in thermal energy, heat transferring and heat interchanging processes. The use of AM with the modified system pulse control will reduce the derivation of the stator temperature, the temperature of AM up to 12 times compared to derivation of the stator temperature, the temperature of AM at direct start. The optimal thermal conditions of AM at rate of change pulse duty factor coefficient equal to 0,16 pu/s is provided. The results of research can be used to optimize the design of pulse control systems, thermal protection of AM with the modified system for heavy-duty, where the frequency of starts reaches 3000 cycles per hour.Item Застосування автоматичних стрілок тролейбусу як детекторів в системах світлофорного авторегулювання(Національний університет "Запорізька політехніка", 2014) Трушевський, Вячеслав Едуардович; Trushevsky, V. E.UK: Для удосконалення світлофорного регулювання пропонується пристрій з пасивним датчиком, що передає сигнал про приближення до перехрестя тролейбусу та напрям його подальшого руху на дорожній контролер. EN: Mismatch traffic light regimes of dynamic traffic flow lead to the formation of congestion, worsening environmental situation, leading to downtime of vehicles and passengers loss of time, perform cursory causes of road accidents In systems of isolated traffic light regulation and automatic systems to carry out effectively the adjustment parameter depending on arrival at the control zone of the rolling stock of public transportation systems allow auto to operate mainly on algorithms that depend on the strategies adopted by regulation. For effective use of algorithms active strategies need reliable and timely detection of approaching public transport to the area of regulation. For improvement of the trafficlights regulation at crossroads the device with the passive sensor transferring a signal about approach of a trolley bus to a crossroad and its further movement direction to the road controller is offered.Item Перспективи схемотехнічних рішень і моделювання підсистем електричної тяги при високошвидкісному русі поїздів(Національний університет "Запорізька політехніка", 2014) Міщенко, Т. М.; Mishchenko, T. M.UK: Розглянуто та проаналізовано схемотехніку і параметри перспективних підсистем тягового електропостачання та електрорухомого складу, які зможуть забезпечити впровадження швидкісного і високошвидкісного руху поїздів. Зазначено, що такі підсистеми електричної тяги є занадто складними і до того ж нелінійними, динамічними і потужними, що й обумовлює практичну неможливість побудови їх точних класичних математичних моделей. В роботі пропонується створювати математичні моделі для таких підсистем, а отже і для всієї системи електротяги, методами ідентифікації, параметричної чи структурної. EN: The comparative analysis of advanced circuit solutions and parameters of traction electric supply and electric rolling stock provides the organization and the introduction of high-speed movement of trains on the Railways of Ukraine. It is established that the force of the current system of electric traction with the constant voltage 3,3 kV is appropriate to the stress increase in the traction network in the first stage up to 6 kV, and then to 2 kV due to the transition from the existing centralized system of power supply of the traction to the network distributed power. In the field of electric rolling stock all experts believe that it is necessary to create a universal multi-system locomotives on the basis of brushless electric traction motors, as a rule, asynchronous shorted ones. These subsystems of electric traction, traction electric supply and electric rolling stock are very complex and, in addition, non-linear, dynamic, and powerful ones and this determines the practical impossibility of their exact classical mathematical models construction. It is proposed to create the mathematical model for such subsystems, and thus for the entire system of electric traction by the methods of parametric or structural identification.Item Аналіз енергетичних процесів в трифазному силовому активному фільтрі з використанням спектрального моделювання(Національний університет "Запорізька політехніка", 2014) Власенко, Р. В.; Бялобржеський, О. В.; Vlasenko, R. V.; Bialobrzeski, O. V.UK: В роботі проведено аналіз енергетичних процесів в трифазному силовому активному фільтрі з використанням його спектральної моделі. На підставі існуючих моделей активних випрямлячів розроблена спектральна модель активного фільтра, в результаті отримані графіки потужності та енергії в системі для статичного режиму роботи пристрою за визначених умов. Аналіз отриманих графіків та спектрів відповідних параметрів режиму фільтру дозволив оцінити розподіл електричної енергії в елементах фільтру. EN: The problem of electricity quality to consumers with non-linear, variable load caused the development of technical solutions as a managed device controlled filtering compensates - active power filter is discussed. In known scientific papers the issues of energy redistribution in the power circuit filter elements are clarified. The purpose of this paper is to give analysis of energy processes in a three-phase active power filter using spectral modeling with the presence of poly harmonics mode settings. Based on existing models of active rectifiers the spectral model of the active power filter is developed. For certain conditions for static mode the temporal and spectral dependence of power and energy in the circuit elements is obtained. Analysis of the results revealed that the contours of the device circulating components of high-power compared with the basic harmonic, that circulates between the network and the device, and the fundamental harmonic is absent in the spectrum of the power capacitor. Operation device provides the energy redistribution between phases of the network due to its partial reswitching of reactive elements.Item Влияние расположения заготовок электродов на распределение удельной мощности в керне печи Ачесона(Національний університет "Запорізька політехніка", 2014) Ярымбаш, Дмитрий Сергеевич; Яримбаш, Дмитро Сергійович; Yarymbash, D. S.RU: Предлагается обладающая высокой точностью и эффективностью численной реализации 3D модель электромагнитных и термоэлектрических полей в керне печи Ачесона постоянного и переменного тока, позволяющая учесть особенности конструкции печи и боковых шинных пакетов, пространственное размещение заготовок электродов в токопроводящей пересыпке керна, температурные зависимости электромагнитных и теплофизических свойств материалов, а также технологические режимы графитации. Выполнен анализ пространственного распределения удельной мощности тепловыделения в керне при вертикальном и горизонтальном расположении заготовок электродов в керне. UK: Запропоновано 3D модель електромагнітних та термоелектричних полів у керні печі Ачесона постійного та змінного струмів,що має високу точність і ефективність чисельної реалізації та дозволяє врахувати особливості конструкції печі і бокових шинних пакетів, просторовий розподіл заготовок електродів у струмопровідній пересипці керна, температурні залежності електромагнітних так теплофізичних властивостей матеріалів, а також технологічні режими графітації. Виконано аналіз просторового розподілу питомої потужності тепловиділення у керні при вертикальному та горизонтальному розташуванні заготовок електродів у керні. EN: The modeling of electromagnetic and thermoelectric processes on the basis of numerical realization by finite element method of the generalized three-dimensional models of DC and AC graphitization is proposed. The features of furnace structure and side busbar packages, spatial arrangement of the electrodes blanks in the conductive backfill of core, temperature dependence of the electromagnetic and thermal properties of materials, technological regimes of graphitization are taken into account. The high accuracy and efficiency of numerical implementation are provided. The character and regularities of the spatial distribution of specific thermal power in the core at the vertical and horizontal location of the electrode blanks in the core are defined. It is revealed that the specific electric resistance of the core is determined by the ratio of specific electric resistance of electrode blanks, backfill materials, shunt layers and don’t practically depend on the orientation of the electrodes blanks in the Acheson furnace. It is found that in vertical stacking of blanks in the Acheson furnace core at diametric section blanks more heating capacity is allocated compared with the horizontal transverse stacking. Intensification of the heating, reduction in the duration the campaign and energy are provided.